GLUEMAX Tension Pullers Set

Relieve the Tension. Release the Crease.

Every Crease. Every Length. One Set.

Both GLUEMAX Tension Pullers in one set, so the right bar is ready for any crease that comes into the shop.

Creases fight back. Pull on the low alone and the tension locked in the surrounding metal resists every move. The GLUEMAX Tension Puller Set takes that tension out of the equation. Glue a Tension Tab at each end of the damage, seat the feet, and turn the knob to spread the panel. With the tension relieved, the crease pulls evenly and the metal goes where you want it.

The 36" bar spans long creases, quarter panels, and large collision damage in a single setup. The 18" bar brings the same control to shorter creases, body lines, and areas where a full-length bar won't fit. With both on the cart, you never have to make one length do the other's job.

Each bar's drive mechanism is fully enclosed, protected from glue, dust, and shop debris. Set tension by feel with the hand knob, or run the legs in and out with a power drill for faster setup. Straight and Offset Legs swap by hand in seconds with quick-change pins.

Pair the set with the GLUEMAX Mini Dent Lifter (DF-GM600SP) or the GLUEMAX Spring-Loaded Mini Slide Hammer (DF-GMSH) to pull the lows while tension is held.

The GLUEMAX Tension Puller Set is ideal for:

• Long creases and body line damage (36")
• Shorter creases and tight panel areas (18")
• Large collision damage on doors, quarter panels, and bed sides
• Steel and aluminum panels
• Relieving lateral tension before and during glue pulls
• Repairs where preserving the OEM finish matters

It's built for collision repair shops and PDR technicians.

Two Lengths, Full Coverage The 36" handles long creases and large damage. The 18" fits shorter creases and tight areas a full-length bar can't reach.

Relieves Lateral Tension Spreads the panel to relieve built-up tension, so creases pull evenly instead of fighting back.

Hand Knob Control Turn by hand to set tension in small, precise steps, with fine control by feel at every stage of the repair.

Power Drill Adjustment Run the legs in or out with a power drill for faster setup, then fine tune by hand.

Enclosed Drive Mechanism The drive is housed inside each bar, protected from glue, dust, and shop debris.

Two Leg Sets per Bar Straight Legs give focused tension on creases. Offset Legs angle the feet outward for a wider spread across the panel.

Quick-Change Pins Swap legs by hand in seconds, with no tools needed.

GLUEMAX Tension Tabs Square and Long Tension Tabs come with each bar. The feet grip each tab's raised spine for a secure hold under tension.

Works with the GLUEMAX System Hold tension while pulling lows with the GLUEMAX Mini Dent Lifter or Mini Slide Hammer, and blend highs with the Dent Fix Blending Hammer 4 PC Set (DF-BHSET).

Preserves OEM Finishes Glue pull repair with lateral tension keeps the factory finish intact..

Preserves OEM Finishes
Glue pull repair with lateral tension keeps the factory finish intact.

• (1) GLUEMAX Tension Bar, 36", with Tension Knob
• (1) GLUEMAX Tension Bar, 18", with Tension Knob
• (4) Straight Legs
• (4) Offset Legs
• (8) Square Tension Tabs
• (8) Long Tension Tabs

GLUEMAX Tension Pullers Operating Manual (PDF)

1. Choose the bar. Use the 36" for long creases and large damage, or the 18" for shorter creases and tight areas.
2. Prepare the surface. Clean each tab location and tab face with 99% isopropyl alcohol. Glue bonds best on a panel between 75 and 90°F.
3. Glue and place the Tension Tabs. Glue a tab on solid metal at each end of the damage, in line with the crease, and let it cool to between 75 and 90°F.
4. Set the bar and apply tension. Seat each foot onto its tab's spine. Run the legs in with a power drill if needed, then turn the knob in small increments until the crease begins to relax. Pull lows and blend highs while tension is held.
5. Release and clean up. Turn the knob back to fully release tension, free the tabs with isopropyl alcohol, and remove leftover glue.

Always wear safety glasses, and keep your face out of line with the bar under tension. See the Operating Manual (PDF) for full instructions.